Bell & Gossett e-1510 1.5BC Pump 15 HP 3525 RPM 3 Phase TEFC

Description

During high-head process-pumping work, the Bell & Gossett e-1510 1.5BC 15 HP TEFC uses a 15 HP, 3525 RPM two-pole motor in a base-mounted end suction configuration. The 1.5BC casing provides 2.5-inch suction and 1.5-inch discharge connections. Its center member spacer coupling establishes a defined alignment and service-access consideration for harsh indoor or outdoor process installations.

The TEFC enclosure must be evaluated against the documented installation environment, while the 15 HP motor and speed require pump-curve selection for actual hydraulic duty. The supplied details do not establish a flow or head value. Confirm required pressure, suction conditions, fluid properties, piping resistance, electrical supply, and equipment-access requirements before finalizing the selected assembly.

Key Specifications of the Bell & Gossett e-1510 1.5BC 15 HP TEFC Pump

• The 1.5BC casing provides 2.5-inch suction and 1.5-inch discharge connections for matching process-piping arrangements.
• A 15 HP motor establishes the listed drive capacity for the selected base-mounted high-head process-pumping assembly.
• The 3525 RPM two-pole speed defines the motor-speed reference for confirming approved hydraulic duty and motor selection.
• Totally enclosed fan cooled construction identifies the TEFC motor enclosure specified for this e-1510 configuration.
• A center member spacer coupling provides the stated coupling arrangement for alignment and service-access planning.
• Harsh indoor or outdoor process pumping is the listed application context for evaluating this base-mounted unit.

Hydraulic Performance and Application

The Bell & Gossett end suction pump is listed for harsh indoor or outdoor process-pumping applications. Its 1.5BC casing, 15 HP motor, and 3525 RPM speed define equipment configuration, not a duty point. Select through the applicable e-1510 curve and approved system design. Confirm required flow, head, suction conditions, pressure, fluid characteristics, pipe losses, and motor loading before purchase.

Installation and System Requirements

Confirm compatible three-phase electrical power, motor rotation, environmental suitability for the TEFC enclosure, approved system curve, and suction arrangement before installation. Verify that the 2.5-inch suction and 1.5-inch discharge connections match planned piping. Support pipework independently to avoid casing strain. Reserve clearance around the spacer coupling, then follow official e-1510 procedures for base mounting, alignment, connection, and startup.

Service and Maintenance Considerations

The center member spacer coupling requires adequate clearance for alignment and service planning before pipework or nearby equipment is fixed. Follow official e-1510 procedures for lockout, coupling inspection, alignment, seal checks, and reassembly. Review the TEFC motor enclosure as part of the installed environmental condition. Do not replace coupling components or alter the assembly without verifying the exact approved configuration.

Why Choose the Bell & Gossett e-1510 1.5BC 15 HP TEFC

This configuration combines a 1.5BC base-mounted casing, 15 HP TEFC motor, 3525 RPM speed, and center member spacer coupling. Its 2.5-inch suction and 1.5-inch discharge connections support piping-fit review for process applications. Buyers should compare environmental requirements, motor configuration, coupling service access, and approved hydraulic duty with the applicable e-1510 curve before final selection.

Warranty and Support

Bell & Gossett commercial pumps carry a 1-Year Limited Warranty against defects in materials and workmanship. Coverage starts at installation and ends no later than eighteen months from shipment, whichever occurs first. Seals, gaskets, elastomers, coatings, and other wear parts are excluded unless applicable sales documentation states otherwise. Mulmotor provides pre-purchase product guidance and order-related customer support.

Before Ordering the Bell & Gossett e-1510 1.5BC 15 HP TEFC Pump

Before ordering, verify that your process-pumping system requires a 1.5BC casing with 2.5-inch suction and 1.5-inch discharge connections. You should determine flow and head from the applicable e-1510 curve, then confirm the 15 HP TEFC motor and 3525 RPM speed. Review environmental conditions, fluid requirements, suction layout, piping support, coupling clearance, and installation access before purchase.