Bell & Gossett e-1510 1.5BC Pump 15 HP 3525 RPM 3 Phase ODP

Description

Using a stainless-steel shaft sleeve, the Bell & Gossett e-1510 1.5BC 15 HP ODP 3525 is a base-mounted end suction pump with a 15 HP ODP motor at 3525 RPM. Its 2.5-inch suction and 1.5-inch discharge connections define piping checks for high-rise building water supply and chiller-primary applications.

The listed full or near-full impeller reference is approximately 7.0 inches, but the exact trim must be confirmed from approved submittal data. The ODP enclosure, motor speed, and casing size do not determine operating flow or head. Use the applicable e-1510 curve to validate hydraulic duty, pressure, suction conditions, fluid requirements, electrical compatibility, and project piping resistance.

Key Specifications of the Bell & Gossett e-1510 1.5BC 15 HP ODP 3525 Pump

• The 1.5BC casing provides 2.5-inch suction and 1.5-inch discharge connections for matching building-water and chiller piping.
• A 15 HP motor establishes the listed drive capacity for the selected base-mounted end suction pump configuration.
• The 3525 RPM two-pole speed defines the supplied motor-speed reference for hydraulic duty and electrical review.
• Open drip proof construction identifies the ODP motor enclosure specified for this 15 HP pump assembly.
• A full or near-full approximately 7.0-inch impeller reference requires confirmation against the exact approved pump trim.
• A stainless-steel shaft sleeve is listed as a standard rotating-shaft component for this supplied configuration.
• High-rise water supply and chiller primary service are the stated application contexts for this pump arrangement.

Hydraulic Performance and Application

The Bell & Gossett e-1510 1.5BC is listed for high-rise building water supply and chiller-primary applications. Its 15 HP ODP motor, 3525 RPM speed, and nominal impeller reference do not establish a duty point. Select through the appropriate e-1510 curve and approved system requirements. Confirm flow, head, suction conditions, pressure, fluid characteristics, pipe losses, and motor loading before completing the order.

Installation and System Requirements

Confirm compatible three-phase electrical service, motor rotation, environmental suitability for the ODP enclosure, approved system curve, and suction arrangement before installation. Verify that the 2.5-inch suction and 1.5-inch discharge connections fit planned piping. Support nearby pipework independently to prevent casing strain. Follow official e-1510 instructions for base mounting, alignment, electrical connection, startup, and initial operating checks.

Service and Maintenance Considerations

The stainless-steel shaft sleeve is a listed service-related component that should be evaluated with the applicable seal and rotating-assembly documentation. Verify the approximate 7.0-inch impeller reference against the exact approved trim before parts selection. Follow official lockout, alignment, inspection, and post-service procedures. Do not use a nominal impeller size or series-level parts list as proof of exact component compatibility.

Why Choose the Bell & Gossett e-1510 1.5BC 15 HP ODP 3525

This configuration combines a 1.5BC base-mounted casing, 15 HP ODP motor, 3525 RPM speed, stainless-steel shaft sleeve, and approximately 7.0-inch impeller reference. Its 2.5-inch suction and 1.5-inch discharge dimensions support piping-fit review. Buyers can compare these details for high-rise water supply or chiller-primary service, then verify final hydraulic duty through the applicable e-1510 curve.

Warranty and Support

Bell & Gossett commercial pumps carry a 1-Year Limited Warranty against defects in materials and workmanship. Coverage begins at installation and ends no later than eighteen months from shipment, whichever occurs first. Seals, gaskets, elastomers, coatings, and other wear parts are excluded unless sales documentation states otherwise. Mulmotor provides pre-purchase product guidance and order-related customer support.

Before Ordering the Bell & Gossett e-1510 1.5BC 15 HP ODP 3525 Pump

Before ordering, verify that your high-rise water-supply or chiller-primary system requires a 1.5BC casing with 2.5-inch suction and 1.5-inch discharge connections. You should determine flow and head using the applicable e-1510 curve, then confirm the 15 HP ODP motor and 3525 RPM speed. Review impeller trim, shaft-sleeve requirements, pressure limits, fluid properties, piping support, and service clearance.