Bell & Gossett e-1510 1.5BC Pump 20 HP 3525 RPM 3 Phase ODP

Description

Using a 20 HP ODP motor at 3525 RPM, the Bell & Gossett e-1510 1.5BC ODP is a base-mounted end suction pump with 2.5-inch suction and 1.5-inch discharge connections. Its approximate 7.0-inch full-diameter impeller reference provides a configuration check for industrial high-pressure booster and district-cooling projects requiring an approved pump-curve selection.

The ODP motor enclosure must be matched to the installed environment before final selection. The 1.5BC case, 20 HP motor, and two-pole speed do not define a guaranteed flow or pressure outcome. Use the appropriate e-1510 curve, actual system head, suction conditions, fluid properties, and piping resistance to confirm the selected pump and motor arrangement.

Key Specifications of the Bell & Gossett e-1510 1.5BC ODP Pump

• The 1.5BC casing provides 2.5-inch suction and 1.5-inch discharge connections for matching specified system piping.
• A 20 HP motor establishes the listed drive capacity for the selected industrial or district-cooling application.
• The 3525 RPM two-pole speed defines the motor-speed reference for matching approved hydraulic and electrical requirements.
• Open drip proof construction identifies the ODP motor enclosure specified for the supplied pump configuration.
• A nominal approximately 7.0-inch full-diameter impeller requires confirmation against the exact approved trim before service.
• Industrial high-pressure booster and district cooling are the stated application contexts for this base-mounted assembly.

Hydraulic Performance and Application

The Bell & Gossett end suction pump is listed for industrial high-pressure booster and district-cooling applications. Its casing, motor size, speed, and nominal impeller diameter do not confirm a duty point. Select through the appropriate e-1510 curve and project system resistance. Verify required flow, calculated head, pressure, suction conditions, fluid characteristics, and discharge requirements before finalizing the ordered configuration.

Installation and System Requirements

Confirm compatible three-phase power, motor rotation, environmental suitability for the ODP enclosure, and the approved pump curve before installation. Verify that the 2.5-inch suction and 1.5-inch discharge dimensions match project piping. Support pipework independently to prevent casing strain. Follow official e-1510 instructions for base mounting, alignment, electrical connection, and controlled startup of the assembled pump system.

Service and Maintenance Considerations

Verify the approximate 7.0-inch impeller reference against the exact approved trim before selecting service components or considering hydraulic adjustments. The ODP enclosure requires review of the installed environment during maintenance planning. Follow official e-1510 lockout, alignment, seal inspection, and post-service procedures. Do not use nominal impeller diameter as a substitute for exact parts documentation or pump-curve review.

Why Choose the Bell & Gossett e-1510 1.5BC ODP

This configuration offers a 1.5BC base-mounted casing with 2.5-inch suction and 1.5-inch discharge connections, a 20 HP ODP motor, and 3525 RPM speed. The nominal 7.0-inch impeller reference supports submittal review. Buyers should compare environmental conditions, project duty, pressure requirements, and the applicable e-1510 curve before selecting this industrial or district-cooling arrangement.

Warranty and Support

Bell & Gossett commercial pumps carry a 1-Year Limited Warranty against defects in materials and workmanship. Coverage starts at installation and ends no later than eighteen months from shipment, whichever occurs first. Seals, gaskets, elastomers, coatings, and other wear parts are excluded unless applicable sales documentation states otherwise. Mulmotor can assist with product details and order-related questions before purchase.

Before Ordering the Bell & Gossett e-1510 1.5BC ODP Pump

Before ordering, verify that your industrial booster or district-cooling system requires a 1.5BC casing with 2.5-inch suction and 1.5-inch discharge connections. You should determine flow and head using the applicable e-1510 curve, then confirm the 20 HP ODP motor and 3525 RPM speed. Review environmental conditions, impeller trim, fluid requirements, pressure limits, piping support, and service clearance.